認證資料 Certification Data

官網測試有限公司

  • 聯系人:測試線上
  • 官網地址:http://www.lcxyhbsb.com
  • 經營模式:制造商
  • 主營產品:播音與主持藝術,戲劇影視表演,廣播電視編導, 北京
  • 所在地:北京亦莊經濟技術開發區測試街122號
  • 供應產品:14
進入官網
當前位置:首頁>企業動態> Several key factors of production quality of 3PE anticorrosive SSAW steel pipe manufacturer

Several key factors of production quality of 3PE anticorrosive SSAW steel pipe manufacturer

發布時間:2020-07-07

The key factors of production quality of 3PE anti-corrosion SSAW steel pipe manufacturer: the first is the welding speed of 3PE anti-corrosion steel. The welding speed of 3PE anti-corrosion steel is also one of the main parameters of welding process, which is related to heating system, weld deformation speed and mutual crystallization speed. When welding pipe, the welding quality increases with the increase of welding speed. This is because the shortening of heating time makes the width of edge heating zone narrow and the time of metal oxide formation shortened. If the welding speed is reduced, not only the heating zone becomes wider, but also the width of melting zone changes with the change of heat input, resulting in larger inner burr. In low speed welding, less heat input makes it difficult to weld. If it does not meet the specified value, it is easy to produce defects. The second is the welding pressure of 3PE anti-corrosion SSAW steel pipe manufacturer. The welding pressure of 3PE anti-corrosion steel is one of the main parameters of welding process. After the two edges of pipe blank are heated to the welding temperature, they form common metal grains under the action of extrusion force, that is, mutual crystallization and welding. The welding pressure affects the strength and toughness of weld. If the applied welding pressure is small, the metal welding edge can not be fully pressed, the residual non-metallic inclusions in the weld are not easy to discharge due to the small pressure, the weld strength is reduced, and it is easy to crack after stress; when the pressure is too high, most of the metal reaching the welding temperature is extruded, which not only reduces the weld strength, but also produces defects such as excessive internal and external burr or overlap welding. Therefore, the optimum welding pressure should be obtained according to different specifications. According to practical experience, the unit welding pressure is generally 20 ~ 40MPa. Finally, it is the opening angle of 3PE anticorrosive SSAW steel pipe manufacturer. The opening angle refers to the angle between the two edges of the tube blank in front of the extrusion roll. The size of the opening angle is related to the stability of the burning process and has a great impact on the welding quality. The edge warping of 3PE anti-corrosion spiral steel pipe is a serious quality problem, which seriously affects the image of the product and causes the coating to be scrapped. Some of the warping can be detected at the pipe outlet post, some can only be found at the production and management site, and some problems are not exposed until the pipeline construction site. Once a problem occurs, it is extremely difficult to repair it, and it is difficult to prevent some problems because it takes a long time for some problems to be exposed. Therefore, the warping problem must be prevented and solved in the production process. It can be seen that the quality control of 3PE anti-corrosion steel pipe anti-corrosion coating is relatively complex, some quality problems may escape the quality inspection of the pipe outlet post, flow into the pipeline installation site, and even finally be buried and put into operation. Therefore, it is very necessary to strictly inspect and control the quality of each post from surface treatment, coating to pipe delivery. Only when each process is completed in strict accordance with the requirements of the specification, can the operation quality of each process and the final quality of anti-corrosion pipe be ensured. Among them, preheating process and coating mouth post should be included in the quality inspection system, especially the operation quality inspection and control of coating joint should be attached great importance. Since the advent of 3PE decomposition data in the 1930s, 3PE anti-corrosion steel pipe has excellent shock resistance and seismic resistance. The low-temperature embrittlement temperature of polyethylene is extremely low, which can be used safely in the temperature range of - 60 ℃ - 60 ℃. It has a very strong adaptability to the uneven settlement of pipe foundation. 3PE anti-corrosion steel pipe has been rapidly developed as a kind of superior thermal insulation and anti-corrosion materials, and its utilization scope is more and more common. Because of its complicated construction and clear energy-saving and anti-corrosion function, it is widely used in underground. And believe that through the extension of science and technology, it will still have more brilliant achievements in the future. 3PE anti-corrosion SSAW steel pipe has the advantages of light volume weight, high strength, heat insulation, sound insulation, flame retardant, cold resistance, anti-corrosion, non water absorption, complicated and rapid construction, and has become the indispensable data for the construction, transportation, kerosene, chemical industry, electric power, refrigeration and other industries in terms of heat insulation, anti-corrosion, waterproof and sealing. 3PE anticorrosive steel pipe is used for anticorrosion and cold insulation engineering of various indoor and outdoor pipelines, Jiuhe heating pipeline, local air conditioning pipeline, chemical industry and other industrial pipelines. Quality traceability is also necessary. In view of the concealment of some 3PE anti-corrosion SSAW steel pipe quality problems, it is necessary to trace the quality problems after the quality problems are found, find out the causes and scope of the quality problems, find out all the problematic anti-corrosion steel pipes, and effectively eliminate the quality hidden danger of 3PE anti-corrosion coating. In a word, the superiority of 3PE anticorrosive coating must be guaranteed by strict quality control system. Strict implementation of standard and scientific operation method is the most important to control defects and ensure the yield of 3PE anticorrosive SSAW steel pipe. The key factors of production quality of 3PE anti-corrosion SSAW steel pipe manufacturer: the first is the welding speed of 3PE anti-corrosion steel. The welding speed of 3PE anti-corrosion steel is also one of the main parameters of welding process, which is related to heating system, weld deformation speed and mutual crystallization speed. When welding pipe, the welding quality increases with the increase of welding speed. This is because the shortening of heating time makes the width of edge heating zone narrow and the time of metal oxide formation shortened. If the welding speed is reduced, not only the heating zone becomes wider, but also the width of melting zone changes with the change of heat input, resulting in larger inner burr. In low speed welding, less heat input makes it difficult to weld. If it does not meet the specified value, it is easy to produce defects. The second is the welding pressure of 3PE anti-corrosion SSAW steel pipe manufacturer. The welding pressure of 3PE anti-corrosion steel is one of the main parameters of welding process. After the two edges of pipe blank are heated to the welding temperature, they form common metal grains under the action of extrusion force, that is, mutual crystallization and welding. The welding pressure affects the strength and toughness of weld. If the applied welding pressure is small, the metal welding edge can not be fully pressed, the residual non-metallic inclusions in the weld are not easy to discharge due to the small pressure, the weld strength is reduced, and it is easy to crack after stress; when the pressure is too high, most of the metal reaching the welding temperature is extruded, which not only reduces the weld strength, but also produces defects such as excessive internal and external burr or overlap welding. Therefore, the optimum welding pressure should be obtained according to different specifications. According to practical experience, the unit welding pressure is generally 20 ~ 40MPa. Finally, it is the opening angle of 3PE anticorrosive SSAW steel pipe manufacturer. The opening angle refers to the angle between the two edges of the tube blank in front of the extrusion roll. The size of the opening angle is related to the stability of the burning process and has a great impact on the welding quality. The edge warping of 3PE anti-corrosion spiral steel pipe is a serious quality problem, which seriously affects the image of the product and causes the coating to be scrapped. Some of the warping can be detected at the pipe outlet post, some can only be found at the production and management site, and some problems are not exposed until the pipeline construction site. Once a problem occurs, it is extremely difficult to repair it, and it is difficult to prevent some problems because it takes a long time for some problems to be exposed. Therefore, the warping problem must be prevented and solved in the production process. It can be seen that the quality control of 3PE anti-corrosion steel pipe anti-corrosion coating is relatively complex, some quality problems may escape the quality inspection of the pipe outlet post, flow into the pipeline installation site, and even finally be buried and put into operation. Therefore, it is very necessary to strictly inspect and control the quality of each post from surface treatment, coating to pipe delivery. Only when each process is completed in strict accordance with the requirements of the specification, can the operation quality of each process and the final quality of anti-corrosion pipe be ensured. Among them, preheating process and coating mouth post should be included in the quality inspection system, especially the operation quality inspection and control of coating joint should be attached great importance. Since the advent of 3PE decomposition data in the 1930s, 3PE anti-corrosion steel pipe has excellent shock resistance and seismic resistance. The low-temperature embrittlement temperature of polyethylene is extremely low, which can be used safely in the temperature range of - 60 ℃ - 60 ℃. It has a very strong adaptability to the uneven settlement of pipe foundation. 3PE anti-corrosion steel pipe has been rapidly developed as a kind of superior thermal insulation and anti-corrosion materials, and its utilization scope is more and more common. Because of its complicated construction and clear energy-saving and anti-corrosion function, it is widely used in underground. And believe that through the extension of science and technology, it will still have more brilliant achievements in the future. 3PE anti-corrosion SSAW steel pipe has the advantages of light volume weight, high strength, heat insulation, sound insulation, flame retardant, cold resistance, anti-corrosion, non water absorption, complicated and rapid construction, and has become the indispensable data for the construction, transportation, kerosene, chemical industry, electric power, refrigeration and other industries in terms of heat insulation, anti-corrosion, waterproof and sealing. 3PE anticorrosive steel pipe is used for anticorrosion and cold insulation engineering of various indoor and outdoor pipelines, Jiuhe heating pipeline, local air conditioning pipeline, chemical industry and other industrial pipelines. Quality traceability is also necessary. In view of the concealment of some 3PE anti-corrosion SSAW steel pipe quality problems, it is necessary to trace the quality problems after the quality problems are found, find out the causes and scope of the quality problems, find out all the problematic anti-corrosion steel pipes, and effectively eliminate the quality hidden danger of 3PE anti-corrosion coating. In a word, the superiority of 3PE anticorrosive coating must be guaranteed by strict quality control system. Strict implementation of standard and scientific operation method is the most important to control defects and ensure the yield of 3PE anticorrosive SSAW steel pipe. The key factors of production quality of 3PE anti-corrosion SSAW steel pipe manufacturer: the first is the welding speed of 3PE anti-corrosion steel. The welding speed of 3PE anti-corrosion steel is also one of the main parameters of welding process, which is related to heating system, weld deformation speed and mutual crystallization speed. When welding pipe, the welding quality increases with the increase of welding speed. This is because the shortening of heating time makes the width of edge heating zone narrow and the time of metal oxide formation shortened. If the welding speed is reduced, not only the heating zone becomes wider, but also the width of melting zone changes with the change of heat input, resulting in larger inner burr. In low speed welding, less heat input makes it difficult to weld. If it does not meet the specified value, it is easy to produce defects. The second is the welding pressure of 3PE anti-corrosion SSAW steel pipe manufacturer. The welding pressure of 3PE anti-corrosion steel is one of the main parameters of welding process. After the two edges of pipe blank are heated to the welding temperature, they form common metal grains under the action of extrusion force, that is, mutual crystallization and welding. The welding pressure affects the strength and toughness of weld. If the applied welding pressure is small, the metal welding edge can not be fully pressed, the residual non-metallic inclusions in the weld are not easy to discharge due to the small pressure, the weld strength is reduced, and it is easy to crack after stress; when the pressure is too high, most of the metal reaching the welding temperature is extruded, which not only reduces the weld strength, but also produces defects such as excessive internal and external burr or overlap welding. Therefore, the optimum welding pressure should be obtained according to different specifications. According to practical experience, the unit welding pressure is generally 20 ~ 40MPa. Finally, it is the opening angle of 3PE anticorrosive SSAW steel pipe manufacturer. The opening angle refers to the angle between the two edges of the tube blank in front of the extrusion roll. The size of the opening angle is related to the stability of the burning process and has a great impact on the welding quality. The edge warping of 3PE anti-corrosion spiral steel pipe is a serious quality problem, which seriously affects the image of the product and causes the coating to be scrapped. Some of the warping can be detected at the pipe outlet post, some can only be found at the production and management site, and some problems are not exposed until the pipeline construction site. Once a problem occurs, it is extremely difficult to repair it, and it is difficult to prevent some problems because it takes a long time for some problems to be exposed. Therefore, the warping problem must be prevented and solved in the production process. It can be seen that the quality control of 3PE anti-corrosion steel pipe anti-corrosion coating is relatively complex, some quality problems may escape the quality inspection of the pipe outlet post, flow into the pipeline installation site, and even finally be buried and put into operation. Therefore, it is very necessary to strictly inspect and control the quality of each post from surface treatment, coating to pipe delivery. Only when each process is completed in strict accordance with the requirements of the specification, can the operation quality of each process and the final quality of anti-corrosion pipe be ensured. Among them, preheating process and coating mouth post should be included in the quality inspection system, especially the operation quality inspection and control of coating joint should be attached great importance. Since the advent of 3PE decomposition data in the 1930s, 3PE anti-corrosion steel pipe has excellent shock resistance and seismic resistance. The low-temperature embrittlement temperature of polyethylene is extremely low, which can be used safely in the temperature range of - 60 ℃ - 60 ℃. It has a very strong adaptability to the uneven settlement of pipe foundation. 3PE anti-corrosion steel pipe has been rapidly developed as a kind of superior thermal insulation and anti-corrosion materials, and its utilization scope is more and more common. Because of its complicated construction and clear energy-saving and anti-corrosion function, it is widely used in underground. And believe that through the extension of science and technology, it will still have more brilliant achievements in the future. 3PE anti-corrosion SSAW steel pipe has the advantages of light volume weight, high strength, heat insulation, sound insulation, flame retardant, cold resistance, anti-corrosion, non water absorption, complicated and rapid construction, and has become the indispensable data for the construction, transportation, kerosene, chemical industry, electric power, refrigeration and other industries in terms of heat insulation, anti-corrosion, waterproof and sealing. 3PE anticorrosive steel pipe is used for anticorrosion and cold insulation engineering of various indoor and outdoor pipelines, Jiuhe heating pipeline, local air conditioning pipeline, chemical industry and other industrial pipelines. Quality traceability is also necessary. In view of the concealment of some 3PE anti-corrosion SSAW steel pipe quality problems, it is necessary to trace the quality problems after the quality problems are found, find out the causes and scope of the quality problems, find out all the problematic anti-corrosion steel pipes, and effectively eliminate the quality hidden danger of 3PE anti-corrosion coating. In a word, the superiority of 3PE anticorrosive coating must be guaranteed by strict quality control system. Strict implementation of standard and scientific operation method is the most important to control defects and ensure the yield of 3PE anticorrosive SSAW steel pipe.?/